油井管用非调质钢36Mn2V冶金质量控制技术
鞠艳美, 张 伟, 李法兴
莱芜钢铁集团,山东莱芜 271104
Metallurgical Quality Control of 36Mn2V Non-Quenched and Tempered Steels for Oil Well Pipe
摘要 莱钢立足现有工艺装备,通过采取精料、严格控制电炉终点(碳、磷、温度)、优化脱氧工艺、合理调整精炼 炉渣、连铸保护浇注、钢管轧后控冷等工艺措施,成功生产出36Mn2V油井管用非调质钢。分析了该钢种生产过 程的质量控制要点,并提出工艺控制措施,使生产出的产品具有成分均匀、残余元素含量低、氧含量低、夹杂物少、 晶粒细小的特点,较好地满足了石油工业对高质量油井管的要求。
关键词 :
油井管 ,
36Mn2V ,
精炼 ,
保护浇注 ,
质量控制
Abstract :According to conditions of Laisteel product line, the high quality 36Mn2V tube billet for oil well pipe was successfully developed by adoptting the concentrated feed, fining craft measures and so on terminal process control (TPC), strengthening deoxidation, continuous casting protection casting. On the basis of analysis about the factor of effecting the quality, we can work out the way to solve the problems, to enable the product composition homoge- neous, the remaining element content low, the oxygen content low, the inclusion few, and the crystal grain tiny, which met the requestment of oil industry well.
Key words :
quality control
收稿日期: 2012-03-24
出版日期: 2012-12-15
通讯作者:
鞠艳美
E-mail: lgzwei@126.com
[1]
章守华.合金钢[M].北京:冶金工业出版社,1988.52-62
[2]
陈家祥.连续铸钢手册[M].北京:冶金工业出版社,1991.122-128
[3]
马宗况、俞亚鹏、张文基等.非调质钢N80级油管及接箍料的开发[J].江苏冶金,2002,(1).1~3.
[4]
钟云龙、刘国权、黄建凯等.新型油井管钢33Mn2V的动态再结晶规律研究[J].钢铁,2003,(2).42~45.
[5]
彭自胜、徐景峰、杨敏等.N80级油管典型缺陷分析及控制的工艺实践[J].特殊钢,2006,(5).46~48.
[6]
唐海燕、李京社、王剑斌等. EAF_LF_VD_CC工艺生产石油管线钢39Mn2V纯净度的分析[J]. 特殊钢,2006,(9).61~64.
[7]
史宸兴.实用连铸冶金技术[M].北京:冶金工业出版社,1998.51~55
[1]
赵艳玲,王淑满,王洪兴,常立山. X80管线钢的生产实践 [J]. , 2014, 24(08): 26-29.
[2]
封波,徐昊,高卫,吴六顺,董元篪. LF精炼渣低氟化研究进展 [J]. , 2014, 24(06): 1-5.
[3]
冯光宏, 张宏亮, 张培. 国内外特殊钢轧制与产品质量控制的技术进展 [J]. Journal of Materials Sciences & Technology, 2013, 23(9): 1-6.
[4]
刘志国, 王洪兴. 连铸保护浇注工艺改进 [J]. Journal of Materials Sciences & Technology, 2013, 23(8): 38-41.
[5]
张彩东, 杨晓江, 王 峰, 张大勇. 唐钢RH钢水洁净度分析与研究 [J]. Journal of Materials Sciences & Technology, 2013, 23(8): 9-13.
[6]
杨荣光, 王志刚. 超低硫钢精炼工艺生产实践 [J]. Journal of Materials Sciences & Technology, 2013, 23(5): 34-37.
[7]
成国光, 芮其宣, 秦哲, 张鉴 . 单嘴精炼炉技术的开发与应用 [J]. Journal of Materials Sciences & Technology, 2013, 23(3): 1-10.
[8]
陈 良 , 焦玉莉 , 黄优明. 20CrMnTiH齿轮钢可浇性研究与实践 [J]. Journal of Materials Sciences & Technology, 2012, 22(8): 40-43..
[9]
蔡开科,孙彦辉,田志红. 炼钢-精炼-连铸过程钢水超纯净度控制战略 [J]. Journal of Materials Sciences & Technology, 2012, 22(4): 1-7.
[10]
黄建军, 张新文, 周 伟, 杜志明. 37Mn-1铸坯表面气孔缺陷分析与研究 [J]. Journal of Materials Sciences & Technology, 2012, 22(2): 19-24.
[11]
杨之俊, 杨海滨,王彦杰. 氮在炼钢及连铸过程中的变化及影响因素分析 [J]. Journal of Materials Sciences & Technology, 2011, 21(4): 12-16.
[12]
吴燕萍,凌国胜. RH快速精炼工艺与设备选型 [J]. Journal of Materials Sciences & Technology, 2011, 21(2): 11-14.
[13]
朱波. 齿轮钢中氮含量控制与研究 [J]. Journal of Materials Sciences & Technology, 2011, 21(11): 40-43.
[14]
吕宁宁,于景坤,苏畅. LF炉精炼废渣循环利用的研究进展 [J]. Journal of Materials Sciences & Technology, 2011, 21(10): 1-5.
[15]
赵玉潮, 曾香梅, 郑志强, 宁振, 徐毅, 莫朝文. 配加精炼渣和低价矿生产炼钢用熔剂性球团矿的试验研究 [J]. Journal of Materials Sciences & Technology, 2010, 20(9): 34-39.