Effect of multiple-direction forging on microstructure and mechanical properties of ultra-high strength stainless steel
LENG Huan-hui1, LIU Zhen-bao2, LIANG Jian-xiong2, WANG Xiao-hui2, YANG Zhi-yong2, LUO Hai-wen1
1. School of Metallurgical and Ecological Engineering,University of Science and Technology Beijing, Beijing 100083, China; 2. Institute for Special Steels,Central Iron and Steel Research Institute, Beijing 100081, China
Abstract:The microstructure of martensitic ultra-high strength stainless steel after multiple-direction forging was quantitatively characterized by optical microscope (OM), scanning electron microscope (SEM), back scattering electron diffraction (EBSD) and transmission electron microscope (TEM). The effect of multiple-direction hot forging on the mechanical properties of experimental steel was analyzed. The results showed that with the increase of forging passes, the original austenite grain, martensite lath and lath block size of the experimental steel were gradually refined. After the five cycles of hot-forging, the sizes of prior austenite grains, martensite packets and blocks were refined from 226.1 to 3.2 μm, from 106.1 to 2.9 μm and from 2.3 to 1.5 μm, respectively. Consequently, the mechanical properties of the experimental steel were significantly improved, the yield strength, impact toughness and elongation increased from 1 030 to 1 175 MPa, from 140 to 194 J and from 9.3% to 11.6%, respectively. The strength improvement of experimental steel was attributed to both grain refinement and dislocation strengthening with the later as the main contributor. Moreover, it can be concluded that the two strengthening mechanisms cannot be added linearly but by the square-root rule according to dislocation theory.
冷焕辉, 刘振宝, 梁剑雄, 王晓辉, 杨志勇, 罗海文. 多向锻造对超高强度不锈钢组织及力学性能的影响[J]. 中国冶金, 2021, 31(6): 26-33.
LENG Huan-hui, LIU Zhen-bao, LIANG Jian-xiong, WANG Xiao-hui, YANG Zhi-yong, LUO Hai-wen. Effect of multiple-direction forging on microstructure and mechanical properties of ultra-high strength stainless steel[J]. China Metallurgy, 2021, 31(6): 26-33.
Valiev R Z,Islamgaliev R K,Alexandrov I V. Bulk nanostructured materials from severe plastic deformation [J]. Progress in Materials Science,2000,45(2):103.
Desrayaud C,Ringeval S,Girard S,et al. A novel high straining process for bulk materials—The development of a multipass forging system by compression along three axes [J]. Journal of Materials Processing Technology,2006,172(1):152.
Sitdikov O,Sakai T,Goloborodko A,et al. Effect of pass strain on grain refinement in 7475Al alloy during hot multidirectional forging [J]. Materials Transactions,2004,45(7):2232.
Zherebtsov S V,Salishchev G A,Galeyev R M,et al. Production of submicrocrystalline structure in large-scale Ti-6Al-4V billet by warm severe deformation processing [J]. Scripta Materialia,2004,51(12):1147.
[12]
Mironov S Y,Salishchev G A,Myshlyaev M M,et al. Evolution of misorientation distribution during warm ‘abc’ forging of commercial-purity titanium [J]. Materials Science and Engineering A,2006,418(1/2):257.
[13]
Zherebtsov S,Salishchev G,Galeyev R,et al. Mechanical properties of Ti-6Al-4V titanium alloy with submicrocrystalline structure produced by severe plastic deformation [J]. Materials Transactions,2005,46(9):2020.
[14]
Belyakov A,Sakai T,Miura H. Fine-grained structure formation in austenitic stainless steel under multiple deformation at 0.5 Tm [J]. Materials Transactions,JIM,2000,41(4):476.
[15]
Belyakov A,Sakai T,Miura H. Microstructure and deformation behaviour of submicrocrystalline 304 stainless steel produced by severe plastic deformation [J]. Materials Science and Engineering A,2001,319:867.
[16]
Belyakov A,Sakai T,Miura H,et al. Continuous recrystallization in austenitic stainless steel after large strain deformation[J]. Acta Materialia,2002,50(6):1547.
[17]
Belyakov A,Tsuzaki K,Miura H,et al. Effect of initial microstructures on grain refinement in a stainless steel by large strain deformation [J]. Acta Materialia,2003,51(3):847.
[18]
许秀霞. 超细晶中碳低合金钢的磨料磨损行为研究[D]. 柳州:广西大学,2016.
[19]
Dolzhenko P,Tikhonova M,Belyakov A,et al. Dynamic recrystallization of a high-Mn TWIP steel during multiple Forging at 800 ℃ [C]//Proceedings of the Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures. [S.l.]:AIP,2018:20066.
[20]
WANG C F,WANG M Q,SHI J,et al. Effect of microstructure refine-ment on the strength and toughness of low alloy martensitic steel [J]. Journal of Materials Science and Technology,2007,23(5):659.
[21]
Lambert-Perlade A,Gourgues A F,Besson J,et al. Mechanisms and modeling of cleavage fracture in simulated heat-affected zone microstructures of a high-strength low alloy steel [J]. Metallurgical and Materials Transactions A,2004,35(3):1039.
[22]
Díaz-Fuentes M,Iza-Mendia A,Gutiérrez I. Analysis of different acicular ferrite microstructures in low-carbon steels by electron backscattered diffraction. Study of their toughness behavior [J]. Metallurgical and Materials Transactions A,2003,34:2505.
[23]
Zhao M C,Hanamura T,Qiu H,et al. Lath boundary thin-film martensite in acicular ferrite ultralow carbon pipeline steels [J]. Materials Science and Engineering A,2005,395(1/2):327.
[24]
Morito S,Yoshida H,Maki T,et al. Effect of block size on the strength of lath martensite in low carbon steels [J]. Materials Science and Engineering A,2006,438/439/440(1):237.
Takebayashi S,Kunieda T,Yoshinaga N,et al. Comparison of the dislocation density in martensitic steels evaluated by some X-ray diffraction methods [J]. ISIJ International,2010,50(6):875.
LUO H,WANG X,LIU Z,et al. Influence of refined hierarchical martensitic microstructures on yield strength and impact toughness of ultra-high strength stainless steel[J]. Journal of Materials Science and Technology,2020,51:130.
[31]
雍岐龙. 钢铁材料中的第二相[M]. 北京:冶金工业出版社,2006.
[32]
Krauss G. Martensite in steel:strength and structure[J]. Materials science and engineering A,1999,273:40.