浸入式水口结构对连铸大圆坯质量的影响

doi:10.13228/j.boyuan.issn1006-9356.20220285

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (2462 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为研究不同结构的浸入式水口对大规格连铸圆坯质量的影响,以某钢厂生产断面直径为500 mm的 42CrMo连铸圆坯为背景,对使用侧孔浸入式水口和传统直通浸入式水口的使用效果开展研究。结果表明,采用侧孔浸入式水口浇铸时,结晶器进出水温差由传统直通水口的3.30 ℃提高至3.54 ℃;连铸圆坯中心疏松由1.5级改善至1.0级,中心偏析指数由0.93~1.21降低到0.98~1.02,近表层至近中心碳极差由0.050%~0.075%降至0.035%~0.053%,使用侧孔浸入式水口的连铸圆坯碳偏析得到改善;铸坯内弧侧表层至3/4R处氧化物夹杂物总量减少0.5个/mm²;铸坯从1/4R处向内长度不小于13 μm的硫化物数量减少0.35个/mm²;轧材全氧质量分数平均降低0.000 12%,夹杂物中B类氧化物夹杂均在1.5级以内,钢中大尺寸夹杂物明显减少,钢的洁净度得到改善。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	张洪才
	印传磊
	郑力宁
	翟万里
	石可伟
	张益民

关键词 ：直通水口, 侧孔水口, 结晶器, 中心疏松, 夹杂物

Abstract：In order to study the influence of submerged nozzle with different structures on the quality of large-size continuous casting round billet, the effect of side hole submerged nozzle and traditional straight submerged nozzle on the production of 42CrMo continuous casting round billet with the section diameter of 500 mm was studied. The results show that water temperature difference between the inlet and the outlet of mould increases from 3.30 ℃ to 3.54 ℃ when side hole submerged nozzle is used. The central porosity of continuous casting round billet is improved from grade 1.5 to 1.0, the central segregation index decreases from 0.93~1.21 to 0.98~1.02, and the carbon range from near surface to near center decreases from 0.050%~0.075% to 0.035%~0.053%. The carbon segregation of continuous casting round billet is improved by side hole submerged nozzle. The total amount of oxide inclusions decreases by 0.5/mm² from the surface layer of inner arc side to 3/4R. The quantity of sulfide bigger than 13 μm from 1/4R inward decreases by 0.35/mm²; The total oxygen mass fraction of rolled steel is reduced by 0.000 12% on average, the B-type oxide inclusion in inclusions is all within grade 1.5, large size inclusions are reduced obviously, and the cleanliness of the steel is improved.

Key words： straight nozzle side hole nozzle mould center porosity inclusion

收稿日期: 2022-03-24

作者简介: 张洪才(1974—), 男, 大学专科, 高级工程师; E-mail: zhang781237979@163.com;

引用本文:

张洪才, 印传磊, 郑力宁, 翟万里, 石可伟, 张益民. 浸入式水口结构对连铸大圆坯质量的影响[J]. 中国冶金, 2022, 32(9): 57-63. ZHANG Hong-cai, YIN Chuan-lei, ZHENG Li-ning, ZHAI Wan-li, SHI Ke-wei, ZHANG Yi-min. Influence of submerged nozzle structure on large-size continuous casting round billet quality[J]. China Metallurgy, 2022, 32(9): 57-63.

链接本文:

http://www.zgyj.ac.cn/CN/10.13228/j.boyuan.issn1006-9356.20220285 或 http://www.zgyj.ac.cn/CN/Y2022/V32/I9/57

[1]	张广军,彭继承,张学诚,等. 齿轮钢铸坯碳偏析的改善[J]. 特殊钢, 2010, 31(3): 38.
[2]	蔡开科.连铸坯质量控制[M]. 北京:冶金工业出版社,2010.
[3]	左小坦,陈永峰,张洪彪,等. 连铸工艺参数对40Cr圆坯碳偏析的影响[J]. 中国冶金,2020,30(6):97.
[4]	何鹏. 矩形坯结晶器在电磁搅拌下流场和温度场的研究[D]. 鞍山:辽宁科技大学,2017.
[5]	高泽平,苏振江. 大方坯连铸结晶器浸入式水口结构优化[J]. 炼钢, 2008, 24(2): 42.
[6]	王维维,张家泉,陈素琼,等. 水口侧孔倾角对大方坯结晶器流场和液面波动的影响[J]. 北京科技大学学报,2007,29(8):816.
[7]	顾武安,唐萍,文光华,等. 大方坯连铸四孔浸入式水口的应用研究[J]. 钢铁,2008,43(4):101.
[8]	孙彦辉,韦耀环,蔡开科,等. 宽板坯结晶器内卷渣现象试验研究[J]. 钢铁,2007,42(11):31.
[9]	万晓光,韩传基,蔡开科,等. 连铸板坯结晶器浸入式水口试验研究[J]. 钢铁,2000,35(9):20.
[10]	胡群,张硕,王璞,等. 大方坯结晶器内液面波动与卷渣行为[J]. 中国冶金,2020,30(6):63.
[11]	刘文祥,任磊. 浸入式水口倾角对宽幅连铸结晶器内流动行为的影响[J]. 钢铁,2022,57(1):83.
[12]	张静,马靓,吴会平. 水口结构对连铸中低碳钢流场和温度场的影响[J]. 钢铁, 2019, 54(8): 116.
[13]	孙海波,韩占光,钱宏智,等.注流方式对大方坯连铸结晶器内钢水流动与温度状态影响[J]. 北京科技大学学报,2010,32(9):1131.
[14]	赵志刚,张锦文,王松伟, 等. 自旋式浸入式水口对LZ50车轴钢690 mm连铸坯质量的影响[J]. 特殊钢, 2021, 42(1): 38.
[15]	印传磊,翟万里,蒋栋初,等. 42CrMo钢大尺寸夹杂物的来源与控制[J]. 中国冶金,2021,31(1):36.
[16]	党爱国,崔娟,刘敬军,等. 多孔水口对轴承钢280 mm×325 mm铸坯结晶器钢液流场和温度场的影响[J]. 特殊钢,2016,37(2):12.
[17]	裴英豪,朱涛,王茹玉,等. 水口浸入深度对CSP结晶器内流场的影响[J]. 连铸,2021(6):38.