LNG储罐用高锰钢合金化设计及强韧性

doi:10.13228/j.boyuan.issn1006-9356.20230009

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (3980 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Recently,there is a sharp increase in the number of Liquefied Natural Gas (LNG) dual-fuel green ships. It is attracted more and more attentions that high Mn steels for LNG tank building act as one of key cryogenic materials. Effects of alloying elements and their increments on strength and cryogenic impact toughness were systematically investigated in order to enhance strength and cryogenic impact toughness of high Mn steels for LNG tank building by alloying design. Effects of low-temperature hot-rolling and cooling modes on microstructure and mechanical properties were also analyzed. The results show that the substitutional solid solution elements of Ni,Mo and Al have positive effect on yield strength,Cr has negligible effect on yield strength,and Mn has negative effect on yield strength. Except for Mo,the tensile strength is lowered by the other substitutional solid solution elements. However,the cryogenic impact toughness can be improved by the substitutional solid solution elements. The yield strength and tensile strength can be simultaneously enhanced by interstitial solid solution element of C,whereas it deteriorates cryogenic impact toughness. The strength can be also enhanced by microalloying elements of Nb and V,which can retard recrystallization. Moreover,the partially recrystallized structures are harmful to cryogenic impact toughness. In addition, the obviously strengthening effect can be realized for the addition of 0.3%Nb or 0.5%V (mass fraction). But they deteriorate cryogenic impact toughness. The strengthening of high Mn steels is always accompanied by the deterioration of cryogenic impact toughness,leading to a difficulty in developing high Mn steels with high strength and toughness. However,it is found that the strength can be effectively enhanced and excellent cryogenic toughness can be also obtained at the same time by solid solution strengthening,grain boundary strengthening and deformation mechanism controlling on the basis of Al addition. The excellent cryogenic impact toughness can be obtained for the stacking fault energy ranging from 40 to 44 mJ/m² at room temperature. The solid solution strengthening coefficients of Ni,Mo,Cr,Mn,Al and C are estimated to be 7.0,32.0,0.5,-3.0,22.0 and 290.0 MPa/%,respectively. The present work provides the experimental support for the design of high Mn steels with high strength and toughness.

Key words： metallic material high Mn steel alloying yield strength cryogenic impact toughness

Received: 05 January 2023

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	CHEN Jun
	LIU Ning
	LIU Zhenyu
	WANG Guodong

Cite this article:

CHEN Jun,LIU Ning,LIU Zhenyu等. Alloying design as well as strength and toughness of high Mn steels for LNG tank building[J]. China Metallurgy, 2023, 33(6): 73-80.

URL:

http://www.zgyj.ac.cn/EN/10.13228/j.boyuan.issn1006-9356.20230009 OR http://www.zgyj.ac.cn/EN/Y2023/V33/I6/73

[1]	周守为,朱军龙,单彤文,等. 中国天然气及LNG产业的发展现状及展望[J]. 中国海上油气,2022,34(1):1.
[2]	CHOI J K,LEE S G,PARK Y H,et al. High manganese austenitic steel for cryogenic applications[C]//Proceedings of the Twenty-Second (2012) International Offshore and Polar Engineering Conference. Rhodes: International Society of Offshore and Polar Engineers (ISOPE), 2012:29.
[3]	BOUAZIZ O,ALLAIN S,SCOTT C P,et al. High manganese austenitic twining induced plasticity steels:A review of the microstructure properties relationships[J]. Current Opinion in Solid State and Materials Science,2011,15:141.
[4]	张宁飞,崔志强,王婕,等. 含硅镍低密度钢的温拉伸力学行为及强韧机制[J]. 钢铁,2022,57(10):170.
[5]	昝娜,丁桦,骆小鹏,等. 晶粒尺寸对高锰奥氏体TWIP钢氢脆行为的影响[J]. 中国冶金,2016,26(1):23.
[6]	HADFIELD R A. Hadfield's manganese steel[J]. Science,1888,306:284.
[7]	李彦龙,齐亮,邵传兵,等. 球磨机衬板高锰钢性能改进[J]. 钢铁,2018,53(3):72.
[8]	王涛,胡锋,张志成,等. 不同冲击载荷下10Mn钢和NM500的磨损性能及机理[J]. 中国冶金,2021,31(12):47.
[9]	李建民,姜茂发,孙丽枫,等. 20Mn23AlV钢用低反应性连铸保护渣的开发[J]. 中国冶金,2017,27(12):28.
[10]	KIM Y G,PARK Y S,HAN J K. Low temperature mechanical behavior of microalloyed and controlled-rolled Fe-Mn-Al-C-X alloys[J]. Metallurgical Transactions A,1985,16:1689.
[11]	LEE J,SOHN S S,HONG S,et al. Effects of Mn addition on tensile and Charpy impact properties in austenitic Fe-Mn-C-Al-based steels for cryogenic applications[J]. Metallurgical and Materials Transactions A,2014,45:5419.
[12]	陈欢,孙新军,王小江,等. 高锰奥氏体低温钢力学性能及Hall-Petch关系的研究[J]. 材料科学与工艺,2018,26(5):11.
[13]	KIM H,HA Y,KWON K H,et al. Interpretation of cryogenic-temperature Charpy impact toughness by microstructural evolution of dynamically compressed specimens in austenitic 0.4C-(22-26)Mn steels[J]. Acta Materialia,2015,87:332.
[14]	CHEN J,DONG F T,LIU Z Y,et al. Grain size dependence of twinning behaviors and resultant cryogenic impact toughness in high manganese austenitic steel[J]. Journal of Materials Research and Technology,2021,10:175.
[15]	RITCHIE R O. The conflicts between strength and toughness[J]. Nature Materials,2011,10:817.
[16]	PARK K,JIN K,HAN S,et al. Stacking fault energy and plastic deformation of fully austenitic high manganese steels:effect of Al addition[J]. Materials Science and Engineering A,2010,527:3651.
[17]	CHOI W S,DE COOMAN B C,SANDLÖBES S,et al. Size and orientation effects in partial dislocation-mediated deformation of twinning-induced plasticity steel micro-pillars[J]. Acta Materialia,2015,98:391.
[18]	CHEN J,REN J K,LIU Z Y,et al. The essential role of niobium in high manganese austenitic steel for application in liquefied natural gas tanks[J]. Materials Science and Engineering A,2020,772:138733.
[19]	SUN X J,WANG X J. Microstructure and mechanical properties of a hot-rolled high manganese TWIP steel containing 0.3%V[J]. ISIJ International,2020,60(6):1324.
[20]	REN J K,CHEN Q Y,CHEN J,et al. Role of vanadium additions on tensile and cryogenic-temperature Charpy impact properties in hot-rolled high-Mn austenitic steels[J]. Materials Science and Engineering A,2021,811:141063.
[21]	KUSAKIN P,BELYAKOV A,MOLODOV D A,et al. On the effect of chemical composition on yield strength of TWIP steels[J]. Materials Science and Engineering A,2017,687:82.
[22]	IRVINE K J. The strength of austenitic stainless steels[J]. Tetsu To Hagane,1969,207:1017.
[23]	BOUAZIZ O,ZUROB H,CHEHAB B,et al. Effect of chemical composition on work hardening of Fe-Mn-C TWIP steels[J]. Materials Science and Technology,2011,27:707.
[24]	DE COOMAN B C,KWON O,CHIN K G. State-of-the-knowledge on TWIP steel[J]. Materials Science and Technology,2012,28:513.
[25]	GUTIERREZ-URRUTIA I,ZAEFFERER S,RAABE D. The effect of grain size and grain orientation on deformation twinning in a Fe-22wt.%Mn-0.6wt.%C TWIP steel[J]. Materials Science and Engineering A,2010,527:3552.
[26]	沈逸平,张琪,陈光辉,等. Fe-30Mn-8Al-0.8C 奥氏体低密度钢变形中组织演变及变形机制[J].钢铁,2023,58(3):135.
[27]	邢梅,林方敏,唐立志,等. Al元素对Fe-Mn-Al-C系低密度钢的影响特性综述[J].中国冶金,2022,32(2):15.
[28]	CURTZE S,KUOKKALA V T,OIKARI A,et al. Thermodynamic modeling of the stacking fault energy of austenitic steels[J]. Acta Materialia,2011,59:1068.
[29]	CHEN J,REN J K,LIU Z Y,et al. Interpretation of significant decrease in cryogenic-temperature Charpy impact toughness in a high manganese steel[J]. Materials Science and Engineering A,2018,737:158.
[30]	WANG X J,SUN X J,SONG C,et al. Enhancement of yield strength by chromium/nitrogen alloying in high-manganese cryogenic steel[J]. Materials Science and Engineering A,2017,698:110.
[31]	LI Y,LU Y F,LI W,et al. Hierarchical microstructure design of a bimodal grained twinning-induced plasticity steel with excellent cryogenic mechanical properties[J]. Acta Materialia,2018,158:79.
[32]	SOHN S S, HONG S, LEE J, et al. Effects of Mn and Al contents on cryogenic-temperature tensile and Charpy impact properties in four austenitic high-Mn steels[J]. Acta Materialia,2015,100:39.