|
|
Application of modular finishing rolling technology in high-speed wire production line of stainless steel |
CHEN Lian-yun1, ZHOU Min2, CHEN Ying-juan3, TAN Guang-yao2, MA Jin-jiang4 |
1. Product Design and Research Institute, CISDI Equipment Co., Ltd., Chongqing 402284, China; 2. I&S Products Research Division, CISDI R&D Co., Ltd., Chongqing 401122, China; 3. Equipment System Research Division, CISDI R&D Co., Ltd., Chongqing 401122, China; 4. Steel Rolling and Equipment Business Division, CISDI Engineering Co., Ltd., Chongqing 401122, China |
|
|
Abstract Numerical analysis, finite element analysis and laboratory experiments were used to study the influencing factors and wide spread model of deformation in high-speed wire finishing rolling, the coupling stiffness and stiffness model of modular finishing mill, and the control strategy of steel biting speed drop during high-speed rolling. The upgrade was made in view of long-term problems for poor stability and large fluctuation of product dimensional accuracy caused by inaccurate receiving and discharging profile in the finishing mill of stainless steel high-speed wire production line, the application of modular finishing rolling technology in stainless steel high-speed wire was realized through high adaptability pass system, high stiffness modular high-speed mill and high-speed rolling speed drop control technology. Aiming at the problem that the wire was easy to be scratched at climbing section, the sliding friction climbing guide groove was optimized into the rolling friction three roll guide groove, and the looper before finishing mill was changed into vertical looper. The production results show that the operation of modular finishing mill is stable, the vibration value of bevel gear box is less than 2.8 mm/s, the dimensional accuracy of outlet profile for finishing mill is more than 20% higher than that before the transformation, and the dimensional accuracy and surface quality of the final product are significantly improved.
|
Received: 08 February 2022
|
|
|
|
[1] |
王国栋,吴迪,刘振宇,等.中国轧钢技术的发展现状和展望[J].中国冶金,2009,19(12):1.
|
[2] |
龚俊健,刘金兰.3种主流高线精轧机简介[J].轧钢,2012,29(6):46.
|
[3] |
陈莹卷,周民,马靳江.新一代高速线材核心装备技术的研究与开发[J].中国冶金,2019,29(2):67.
|
[4] |
钱宝华.高速线材低温轧制工艺技术及其工程应用[J].轧钢,2021,38(1):59.
|
[5] |
郭立平,杨贵玲,彭开香,等.热轧带钢宽度控制模型的改进[J].轧钢,2009,26(1):60.
|
[6] |
Kim Jun-hyeoung,Jung Young-gook. Spreading power spectrum of an induction motor drive system by chaotic pulse width modulation method[J].Journal of Electrical Engineering and Technology,2021,16(5): 2685.
|
[7] |
董永刚,张文志,宋剑锋.钢轨万能轧制过程轨头宽展规律的理论和实验研究[J].中国机械工程,2009,20(8):1004.
|
[8] |
周民,陈莹卷,闵建军.高速线材减定径多道次孔型轧制有限元分析及工艺参数优化[J].中国冶金,2014,24(3):4.
|
[9] |
马靳江,周民,陈莹卷.线材减定径关键工艺装备技术的研究与开发[J].中国冶金,2018,28(10):62.
|
[10] |
李维刚,冯宁,赵云涛,等.基于广义可加模型的热轧变形抗力预报[J].钢铁研究学报,2018,30(6):447.
|
[11] |
高亦斌,刘月,刘战英.高速线材精轧机组的最小张力优化[J].中国冶金,2015,25(11):26.
|
[12] |
曹树卫.高速线材轧机轧制堆钢产生原因及对策[J].轧钢,2003,20(1):64.
|
[13] |
范群,孙大乐,戚向东.热连轧机工作辊动态负载辊缝计算与应用分析[J].钢铁研究学报,2015,27(1):40.
|
[14] |
Chenna Krishna S,Karthick N K,Abhay K Jha.Effect of hot rolling on the microstructure and mechanical properties of nitrogen alloyed austenitic stainless steel[J].Journal of Materials Engineering and Performance,2018, 27(5):2388.
|
[15] |
周民,陈莹卷,马靳江,等.高速线材减定径机组轧件热变形研究[J].轧钢,2013,30(2):31.
|
[16] |
刘东,吉年丰.模块化轧机控制系统在高速棒材生产线中的应用[J].冶金自动化,2020,44(6):84.
|
|
|
|