|
|
Effect of Ce on inclusion evolution for 440C stainless bearing steel |
MA Shuai1, LI Yang1, JIANG Zhou-hua1, SUN Meng1, CHEN Chang-yong2, LIU Hang3 |
1. School of Metallurgy, Northeastern University, Shenyang 110819, Liaoning, China; 2. School of Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, Hubei, China; 3. Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, Liaoning, China |
|
|
Abstract In order to explore the modification effect of rare earth Ce on the inclusions in 440C stainless bearing steel, a laboratory MoSi2 resistance furnace was used to treat 440C stainless bearing steel with rare earth Ce, and the effects of Ce addition on deoxidation and inclusion evolution of 440C stainless bearing steel were systematically analyzed by OM and SEM. The results show that with the increase of Ce addition, the yield gradually increases. The mass fraction of TO in steel is reduced from 0.002 5% to 0.001 2% by addition of Ce. The inclusions in steel without Ce element are mainly Al2O3, MnS and magnesium aluminum spinel, while the inclusions are modified to Ce-Al-O-based inclusions by adding 0.011 5% Ce. When the amount of Ce added reaches 0.036 4%, the inclusions are completely modified to Ce-O-S inclusions. The size and area ratio of inclusions can be reduced by a moderate amount of Ce, but the size of inclusions will be increased due to excessive addition of Ce. Under the test conditions, when the mass fraction of Ce is 0.011 5%, the fine dispersion effect of inclusions in steel is the most obvious. This study can provide a reference for the application of Ce in high-carbon chromium stainless bearing steel.
|
Received: 20 December 2021
|
|
|
|
[1] |
李安玲, 何强, 张勇. 440C高温不锈钢作为轴承钢的发展现状[J]. 安阳工学院学报, 2017, 04(4): 13.
|
[2] |
梁良华, 李笃信, 李昆, 等. 440C不锈钢金属注射成形工艺研究[J]. 粉末冶金工业, 2007(6): 44.
|
[3] |
LIU Feng-bin, FU Guo-hao, CUI Yan, et al. Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels[J]. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, 2013, 307(8): 412.
|
[4] |
Courbon J, Lormand G, Dudragne G, et al. Influence of inclusion pairs, clusters and stringers on the lower bound of the endurance limit of bearing steels[J]. Tribology International, 2003, 36(12): 921.
|
[5] |
Hashimoto K, Fujimatsu T, Tsunekage N, et al. Study of rolling contact fatigue of bearing steels in relation to various oxide inclusions[J]. Materials and Design, 2011, 32(3):1605.
|
[6] |
ZHANG J M, LI S X, YANG Z G. Influence of inclusion size on fatigue behavior of high strength steels in the gigacycle fatigue regime[J]. International Journal of Fatigue, 2007, 29(4): 765.
|
[7] |
杨超云. 稀土对高碳铬轴承钢夹杂物-组织-性能的影响机理研究[D]. 合肥: 中国科学技术大学, 2020.
|
[8] |
谌智勇, 储焰平, 杨文, 等. 重轨钢脱氧过程中非金属夹杂物生成热力学及工业实践[J]. 炼钢, 2020, 36(4): 12.
|
[9] |
肖微, 包燕平, 王敏, 等. 非铝脱氧GCr15轴承钢的夹杂物演变和控制[J]. 钢铁, 2021, 56(1): 37.
|
[10] |
LIU X G, WANG C, GUI J T, et al. Effect of MnS inclusions on deformation behavior of matrix based on in-situ experiment[J]. Materials Science and Engineering, 2019, 746(11): 239.
|
[11] |
LIU Xiao, YANG Ji-chun, YANG Lin, et al. Effect of Ce on inclusions and impact property of 2Cr13 stainless steel[J]. Journal of Iron and Steel Research, International, 2010, 17(12): 59.
|
[12] |
杨吉春,栗宏伟,周莉,等. 微量稀土铈在超洁净IF钢中的作用[J]. 钢铁, 2015, 50(11): 81.
|
[13] |
孙萌, 姜周华, 李阳, 等. Ce-Mg复合处理对含硫齿轮钢SCr420H洁净度的影响[J]. 钢铁, 2021, 56(7): 47.
|
[14] |
习小军, 杨树峰, 李京社, 等. 含铈304不锈钢夹杂物改性及耐腐蚀性能优化[J]. 钢铁, 2020, 55(1): 20.
|
[15] |
康健, 于彦冲, 孟晓亮, 等. 稀土处理HRB400E钢洁净度研究[J]. 连铸, 2020(3): 38.
|
[16] |
杨超云, 栾义坤, 李殿中, 等. 稀土元素对高洁净度轴承钢中夹杂物的影响研究[J]. 炼钢, 2016, 32(4): 54.
|
[17] |
GAO Jin-zhu, FU Pai-xian, LIU Hong-wei, et al. Effects of rare earth on the microstructure and impact toughness of H13 steel[J]. Metals, 2015, 5(1): 383.
|
[18] |
杨超云, 庄权, 刘航, 等. 稀土变质高洁净轴承钢中夹杂物的行为分析[J]. 中国冶金,2020, 30(9): 45.
|
[19] |
董方, 蔡国君, 储少军. 稀土铈对1Cr18Mn8Ni5N不锈钢力学性能的影响[J]. 钢铁, 2010, 45(11): 82.
|
[20] |
刘晓, 杨吉春, 高学中. 稀土2Cr13不锈钢中夹杂物的热力学分析及试验研究[J]. 钢铁, 2010, 45(8): 65.
|
|
|
|