TiN对高强度耐磨钢韧性的影响及其机制分析

doi:10.13228/j.boyuan.issn1006-9356.20200652

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4792 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要采用 SEM、EDS、TEM等技术,结合热力学软件,研究Ti含量对低合金耐磨钢低温冲击韧性的影响、断口夹杂物尺寸和形态以及夹杂物形态与冲击韧性的关系。结果表明,Ti元素质量分数为0.03%的低合金耐磨钢的低温(-40 ℃)冲击性能最好,可达33.0 J;断口夹杂物TiN的形态呈现3种形貌,即出现细窄裂纹、出现孔洞以及直接被撕裂;随着Ti含量的增加,夹杂物形态由完整到破碎。分析TiN的破碎机制发现,TiN破碎由2种机制产生,即裂纹扩展形成孔洞导致破碎、主裂纹衍生出更多的次裂纹导致破碎。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	王帅
	胡锋
	李德发
	周雯
	吴开明

关键词 ：低合金耐磨钢, 低温冲击, 夹杂物TiN, 破碎机制, 裂纹

Abstract：SEM, EDS, TEM and other technologies combined with thermodynamic software were used to study the effect of Ti content on the low-temperature impact toughness of low-alloy wear-resistant steel, size and morphologies of fracture inclusions, and the relationship between morphologies of inclusions and impact toughness. The results showed that the low-alloy wear-resistant steel with a Ti mass fraction of 0.03% had the best low-temperature (-40 ℃) impact performance, which could reach 33.0 J. The morphology of TiN inclusion in the fracture surface showed three types of morphologies, namely, narrow cracks, holes and tearing crack. With the increase of Ti content, the morphology changed from intact to broken. Analysis of the breaking mechanism of TiN revealed that TiN breaking was caused by two mechanisms, namely, cracks propagated to form holes leading to breakage and the main cracks derived more secondary cracks and cause breaking.

Key words： low-alloy wear-resistant steel low-temperature impact TiN inclusion breaking mechanism crack

收稿日期: 2020-11-17

基金资助:国家自然科学基金资助项目(51671149); 湖北省自然科学基金资助项目(2016CFA004,T201903); 武汉市科技局应用基础前沿专项资助项目(2019010701011382); 111项目和武汉科技大学科发院重大科技资助项目(2018TDX07)

通讯作者: 吴开明(1966—), 男, 博士, 教授; E-mail: wukaiming@wust.edu.cn

作者简介: 王帅(1995—), 男, 硕士生; E-mail: wangshuai_chang@163.com。

引用本文:

王帅, 胡锋, 李德发, 周雯, 吴开明. TiN对高强度耐磨钢韧性的影响及其机制分析[J]. 中国冶金, 2021, 31(7): 38-45. WANG Shuai, HU Feng, LI De-fa, ZHOU Wen, WU Kai-ming. Effect of TiN on toughness of high-strength wear-resistant steel and its mechanism analysis[J]. China Metallurgy, 2021, 31(7): 38-45.

链接本文:

http://www.zgyj.ac.cn/CN/10.13228/j.boyuan.issn1006-9356.20200652 或 http://www.zgyj.ac.cn/CN/Y2021/V31/I7/38

[1]	符寒光,邢建冬. 耐磨铸件制造技术[M]. 北京:机械工业出版社,2009.
[2]	SHI C B,LIU W J,LI J,et al. Effect of boron on the hot ductility of low-carbon Nb-Ti-Microalloyed steel[J]. Materials Transactions,2016,57:647.
[3]	杨跃标,李宗强,邓深,等. 热轧钛微合金化高强钢低温冲击韧性的控制[J]. 钢铁,2021,56(3):41.
[4]	潘小燕,梁亮. 基于超硬TiC增强耐磨性超级耐磨钢研究与应用[J]. 涟钢科技与管理,2020(1):13.
[5]	杨跃标,邓深,樊雷,等. 钛微合金化高强钢的组织性能及强化机制[J]. 钢铁,2019,54(10):72.
[6]	傅杰,朱剑,迪林,等. 微合金钢中TiN的析出规律研究[J]. 金属学报,2000,36(8):801.
[7]	GUI L T,LONG M J,ZHANG H H,et al. Study on the precipitation and coarsening of TiN inclusions in Ti-microalloyed steel by a modified[J]. Journal of Materials Research and Technology,2020,9(3):5499.
[8]	孙新军,焦兰,宋宁,等. Ti、N含量对焊接出晶区晶粒尺寸及韧性的影响[J]. 材料热处理学报,2010,31(10):44.
[9]	LIANG W,WU R,YUAN Q,et al. Investigation on precipitation behavior and morphology of TiN particles in high-Ti low-carbon high-strength steel[J]. Trans Indian Institute of Metals,2020,73:151.
[10]	吴翔,左秀荣,赵威威,等. NM500耐磨钢拉伸过程中TiN破碎机制研究[J]. 金属学报,2020,56(2):129.
[11]	郭文营,胡小强,马晓平,等. TiN析出相对中碳Cr-Mo耐磨钢凝固组织的影响[J]. 金属学报,2016,52(7):769.
[12]	田钱仁. GCr15轴承钢中TiN夹杂物析出与演变机制[D]. 鞍山:辽宁科技大学,2019.
[13]	Prikryl M,Kroupa A,Weatherly G C,et al. Precipitation behavior in a medium carbon,Ti-V-N microalloyed steel[J]. Metallurgical and Materials Transactions A,1996,27(5):1149.
[14]	KANG Y,MAO W M,CHEN Y J,et al. Effect of Ti content on grain size and mechanical properties of UNS S44100 ferritic stainless steel[J]. Materials Science and Engineering A,2016,677:211.
[15]	毛新平,孙新军,康永林,等. EAF-CSP流程钛微合金化高强钢板的组织和性能研究[J]. 钢铁,2005,40(9):65.
[16]	XIE Z J,SHANG C J,WANG X L,et al. Microstructure-property relationship in a low carbon Nb-B bearing ultra-high strength steel by direct-quenching and tempering[J]. Materials Science and Engineering A,2018,727:200.
[17]	Fairchild D P,Howden D G,Clark W A T. The mechanism of brittle fracture in a microalloyed steel:Part I. Inclusion-induced cleavage[J]. Metallurgical and Materials Transactions A,2000,31(3):641.